HIKVISION 24 Port Gigabit Smart POE Switch

General

ShellMetal material

Net Weight2.96 kg (6.52 lb)

Gross Weight3.2 kg (7.05 lb)

Dimensions (W × H × D)440.0 mm × 220.8 mm × 44.0 mm (17.32” × 8.69” × 1.73”)

Operating Temperature0 °C to 45 °C (0 °F to 113 °F)

Storage Temperature-40 °C to 85 °C (-40 °F to 185 °F)

Operating Humidity5% to 95% (no condensation)

Relative Humidity5% to 95% (no condensation)

Power Supply100~240 VAC, 50/60 Hz, Max. 4 A

Installation ModeRack (equipped with mounting ears)

Max. Power Consumption250 W

Power Consumption in Idle30 W

Surge Protection6 KV

Network Parameters

Ports24 × Gigabit PoE port,1 × Gigabit RJ45 port,1 × Gigabit fiber optical port

MAC Address Table8 K

Switching Capacity56 Gbps

Packet Forwarding Rate41.66 Mpps

Internal Cache4.1 Mbits

PoE Power Supply

PoE StandardIEEE 802.3af,IEEE 802.3at

PoE Power Pin8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)

PoE PortPoE: Ports 1 to 24

Max. Port Power30 W

PoE Power Budget230 W

Software Function

Long Range

Ports 1 to 24: up to 300 m.

Long range performance may vary depend on camera model or cable condition.

Port Isolation

Ports 1 to 24: port isolation mode to improve network security.

Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE Watchdog Ports 1  to 24: auto detect and restart the cameras that do not respond.

Link Aggregation

Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection.

Support static link aggregation.

Support 8 aggregation groups.

Loop Prevention

Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default.

Support 802.1D STP.

Suppport 802.1w RSTP.

VLAN

VLAN is used for network scale planning and network health improvement.

Support 802.1Q.

Configurable VLAN ID from 1-4094.

Support Trunk, Access port mode.

Support Max. 32 VLAN.

HPP

Support one-click activation and remote management via Hik-Partner Pro. Functions supported:

Display the port rate.

Display the port bandwidth utilization rate.

Display the PoE power usage.

Display topology information.

Display the alarm status.

Restart ports and devices.

Enable port long-rage mode.

Remotely upgrade the device.

System Maintenance

Support device management via web.

Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses.

Support Super IP, which is a fixed IP address (10.180.190.200) for direct access.

Support remote management via Hik-Partner Pro.

Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected.

Support 802.1ab LLDP for peer device discovery.

Support port mirroring for fault locating.

Approval

EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)

SafetyCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)

Chemistry

CE-RoHS (201165EU);

WEEE (201219EU);

Reach (Regulation (EC) No.19072006)